| ClabsDocsisVersion |
enumeration |
Indicates the DOCSIS Radio Frequency specification being
referenced.
'docsis10' indicates DOCSIS 1.0.
'docsis11' indicates DOCSIS 1.1.
'docsis20' indicates DOCSIS 2.0.
'docsis30' indicates DOCSIS 3.0.
'docsis31' indicates DOCSIS 3.1. |
| DsOfdmCyclicPrefix |
uint32 |
This data type is defined to indicate the five possible values
for the length of cyclic prefix. This represents the number
of samples of the 204.8 MHz clock |
| DsOfdmModulationType |
enumeration |
This data type is defined to indicate the bit loading of
subcarriers in an OFDM downstream channel. |
| DsOfdmRollOffPeriod |
uint32 |
This data type is defined to indicate the five possible values
for the windowing roll-off period. This represents the number
of samples of the 204.8 MHz clock. |
| EmIdList |
string |
A list of Energy Management Ids displayed as a comma-separated
list of 15-bit hexadecimal values. These values are encoded into
16-bits but the high-order bit is always 0. |
| HundredthdB |
int32 |
This data type represents power levels that are normally
expressed in dB. Units are in hundredths of a dB;
for example, 5.17 dB will be represented as 517. |
| HundredthdBmV |
int32 |
This data type represents power levels that are normally
expressed in dBmV. Units are in hundredths of a dBmV;
for example, 5.17 dBmV will be represented as 517. |
| OfdmProfiles |
bits |
This data type enumerates the configured channel profiles on
the CM. |
| PartialChannelType |
bits |
This data type enumerates each of the possible profiles or channel
attributes which can contribute to an OFDM channel being considered
a Partial Channel by the MAC layer. As more than one of these error
conditions can exist at the same time this data type is based on a
BITS data type. The bits from low to high are:
Bit 0: fecErrorsDsProfile
Bit 1: fecErrorsNcpProfile
Bit 2: fecErrorsPlc |
| PartialChanReasonType |
enumeration |
This data type enumerates the CM-STATUS events which
a CM can utilize to report a Partial Channel situation. |
| PartialServiceType |
enumeration |
This data type enumerates the type of channel issue which the
MAC Layer indicates is causing the CM to be in DOCSIS 3.0 Partial
Service mode. The possible values are as follows:
other(1)
none(2)
partialSvcDsOnlyImpaired(3)
partialSvcUsOnlyImpaired(4)
partialSvcDsAndUsImpaired(5) |
| PartialSvcReasonType |
enumeration |
This data type enumerates the CM-STATUS events which
a CM can utilize to report a Partial Service situation. |
| PrimaryDsIndicatorType |
enumeration |
This data type is defined to represent the channel indicator
type for the downstream channel. |
| SubcarrierSpacingType |
int32 |
This data type defines the subcarrier spacing for the FFT
mode in use. For downstream OFDM channels, if the FFT mode
is 4K mode, then spacing is 50 kHz; if it is 8K mode, then
the spacing is 25 kHz. For upstream OFDMA channels, if the
FFT mode is 2K mode, then the spacing is 50kHz; if the mode
is 4K mode, then the spacing is 25kHz. In units of kHz. |
| TimeInterleaverDepth |
uint32 |
This data type is defined to indicate the depth of time
interleaving used for this downstream channel in symbols. |
| UsOfdmaCyclicPrefix |
uint32 |
This data type is defined to indicate the eleven possible values
for the length of cyclic prefix. The cyclic prefix represents the
number of samples of the 204.8 MHz clock. |
| UsOfdmaModulationType |
enumeration |
This data type is defined to indicate the bit loading of
subcarriers in an OFDMA upstream channel. |
| UsOfdmaRollOffPeriod |
uint32 |
This data type is defined to indicate the eight possible values
for the windowing roll-off period. This represents the number
of samples of the 204.8 MHz clock |