This module contains a collection of YANG definitions for wireless common enum types. Copyright (c) 2016-2021 by Cisco Systems, ...
Version: 2021-07-01
module Cisco-IOS-XE-wireless-enum-types { yang-version 1; namespace "http://cisco.com/ns/yang/Cisco-IOS-XE-wireless-enum-types"; prefix wireless-enum-types; import cisco-semver { prefix cisco-semver; } organization "Cisco Systems, Inc."; contact "Cisco Systems, Inc. Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 1800 553-NETS E-mail: cs-yang@cisco.com"; description "This module contains a collection of YANG definitions for wireless common enum types. Copyright (c) 2016-2021 by Cisco Systems, Inc. All rights reserved."; revision "2021-07-01" { description "- Added enumeration for 6 GHz radio band - Added new enum for country codes - Added enumeration for AP antenna interface type - Added enumeration for radio service type - Added an enumeration for antenna beam selection"; reference "3.7.0"; } revision "2021-03-01" { description "- Added enums for neighbor discovery mode and capability for AP - Added enum for LAN port configuration"; reference "3.6.0"; } revision "2020-11-01" { description " - Added enum for open rrm remote leader reset reason - Deprecated Rogue RLDP enumerations"; reference "3.5.0"; } revision "2020-07-01" { description "- Added BLE LTX feature - Added enum for rule action type - Added enum for rule application - Added enums for support bundle transfer status and mode - Added enums for country codes - Added enums for controller name config in access point - Added enum for for the case of not allowing cross-connect providing WiFi direct clients - Added enum for BLE device SIM interface for virtual AP"; reference "3.4.0"; } revision "2020-03-01" { description "- Added enum for controller index - Added enum indicating number of 802.11k Beacon Radio Measurement Requests to send - Added enum for 802.11k Beacon Radio Measurement Modes for Client Scan Reports - Added enum indicating trigger which sent a 802.11k Beacon Radio Measurement Request"; reference "3.3.0"; } revision "2019-11-01" { description "- Added enum for NAC type - Added a new enum for P2P blocking action - Added enum for IPv6 CAPWAP data UDP-Lite checksum - Modified NAC type description - Added dual radio mode and FRA capable parameters - Added enum for IPv6 Neighbour Discovery(ND) proxy state - Added enum for highest throughput supported by radio"; reference "3.2.0"; } revision "2019-05-01" { description "- Added enums for timer profile action - Added enums for mfp - Added enums for 802.11u - Changed enum for Hotspot 2.0 to give correct version names - Added semantic version"; reference "3.1.0"; } revision "2019-02-19" { description "- Added new enum for Channel switch mode - Change EoGRE enum - Added support for Flex recovery (FT) EoGRE matching enum - Added support for secondary 80 channel for 80+80 MHz Channel width - Added enum for dot11ax MCS rate index - Cleaned up spelling errors in descriptions - Changed eogre-client-match-v2 to a clearer eogre-client-match-reason - Added new enum for NDP data type - Added enum for RRM channel change type - New enum showing if a wired vlan is associated to Guest-LAN profile - Added enum for DCA threshold and Data rate threshold of Optimized Roaming - Added new enum for Radio's neighbor channel width"; reference "3.0.0"; } revision "2018-05-18" { description "Removed enumerations for sip codec support"; reference "2.2.0"; } revision "2018-03-22" { description "Add enum for multicast support"; reference "2.1.0"; } revision "2018-01-24" { description "The first generally available version"; reference "2.0.0"; } revision "2017-05-05" { description "Initial revision"; reference "1.0.0"; } cisco-semver:module-version "3.7.0"; cisco-semver:module-version "3.6.0"; cisco-semver:module-version "3.5.0"; cisco-semver:module-version "3.4.0"; cisco-semver:module-version "3.3.0"; cisco-semver:module-version "3.2.0"; cisco-semver:module-version "3.1.0"; cisco-semver:module-version "3.0.0"; cisco-semver:module-version "2.2.0"; cisco-semver:module-version "2.1.0"; cisco-semver:module-version "2.0.0"; cisco-semver:module-version "1.0.0"; typedef apf-vap-p2p-blocking-action { type enumeration { enum "p2p-blocking-action-none" { value 0; description "Peer to peer blocking action None"; } enum "p2p-blocking-action-fwdup" { value 1; description "Peer to peer blocking action Forward Upstream"; } enum "p2p-blocking-action-drop" { value 2; description "Peer to peer blocking action Drop"; } enum "p2p-blocking-action-allow-private-group" { value 3; description "Peer to peer blocking action Allow Private Group"; } } description "Enables point to point communication - Not supported in EWLC"; } typedef dot11ac-mcs-rate-index { type enumeration { enum "enm-dot11ac-mcs-idx-8" { value 8; description "MCS data rate for index 8"; } enum "enm-dot11ac-mcs-idx-9" { value 9; description "MCS data rate for index 9"; } } description "Enum for Dot11ac MCS Data rate index"; } typedef rrm-chan-width { type enumeration { enum "rrm-channel-width-20-mhz" { value 20; description "Channel width 20 MHz"; } enum "rrm-channel-width-40-mhz" { value 40; description "Channel width 40 MHz"; } enum "rrm-channel-width-80-mhz" { value 80; description "Channel width 80 MHz"; } enum "rrm-channel-width-160-mhz" { value 160; description "Channel width 160 MHz"; } enum "rrm-channel-width-80-80-mhz" { value 188; description "Channel width 188 MHz"; } } description "RRM channel width"; } typedef radio-neighbor-chan-width { type enumeration { enum "radio-neighbor-chan-width-20-mhz" { value 0; description "Channel width 20 MHz"; } enum "radio-neighbor-chan-width-40-mhz-above" { value 1; description "Channel width 40 MHz Above"; } enum "radio-neighbor-chan-width-40-mhz-below" { value 2; description "Channel width 40 MHz Below"; } enum "radio-neighbor-chan-width-80-mhz" { value 6; description "Channel width 80 MHz"; } enum "radio-neighbor-chan-width-160-mhz" { value 7; description "Channel width 160 MHz"; } enum "radio-neighbor-chan-width-8080-mhz" { value 8; description "Channel width 80+80 MHz"; } } description "channel width of neighbor radio"; } typedef apf-ms-data-upsd-bronze { type enumeration { enum "bk1" { value 0; description "Background data -1"; } enum "bk2" { value 1; description "Background data -2"; } enum "bk3" { value 2; description "Background data -3"; } enum "bk4" { value 3; description "Background data -4"; } } description "Enum type for data upsd bronze"; } typedef apf-ms-data-upsd-silver { type enumeration { enum "be1" { value 0; description "Best effort data -1"; } enum "be2" { value 1; description "Best effort data -2"; } enum "be3" { value 2; description "Best effort data -3"; } enum "be4" { value 3; description "Best effort data -4"; } } description "Enum type for data upsd silver"; } typedef apf-ms-data-upsd-gold { type enumeration { enum "vi1" { value 0; description "Video data -1"; } enum "vi2" { value 1; description "Video data -2"; } enum "vi3" { value 2; description "Video data -3"; } enum "vi4" { value 3; description "Video data -4"; } } description "Enum type for data upsd gold"; } typedef apf-ms-data-upsd-platinum { type enumeration { enum "vo1" { value 0; description "Voice data -1"; } enum "vo2" { value 1; description "Voice data -2"; } enum "vo3" { value 2; description "Voice data -3"; } enum "vo4" { value 3; description "Voice data -4"; } } description "Enum type for data upsd platinum"; } typedef enm-mcast-client-status { type enumeration { enum "mc-only" { value 0; description "MC only"; } enum "mc2uc-pending" { value 1; description "MC-UC pending"; } enum "mc2uc-allowed" { value 2; description "MC-UC allowed"; } enum "mc2uc-deny" { value 3; description "MC-UC deny"; } enum "re-rrc-deny" { value 4; description "Re RRC deny"; } enum "re-rrc-demote" { value 5; description "Re RRC demote"; } enum "mc2uc-deny-no-blacklist" { value 6; description "MC-UC deny no blacklist"; } } description "Multicast client status"; } typedef media-stream-qos { type enumeration { enum "mstream-besteffort" { value 0; description "best effort"; } enum "mstream-background" { value 1; description "background"; } enum "mstream-video" { value 4; description "This object specifies the Video QoS Over the Air"; } enum "mstream-voice" { value 6; description "This object specifies the Voice QoS Over the Air"; } } description "Specifies the type of media stream used"; } typedef enm-radio-type { type enumeration { enum "radio-invalid" { value 0; description "Radio invalid"; } enum "radio-80211bg" { value 1; description "Radio 80211bg"; } enum "radio-80211a" { value 2; description "Radio 80211a"; } enum "radio-80211abgn" { value 3; description "Radio 80211abgn"; } enum "radio-uwb" { value 4; description "Radio UWB"; } enum "radio-remote-lan" { value 8; description "Radio remote LAN"; } enum "radio-80211-6ghz" { value 16; description "Radio 80211 6 GHz"; } } description "Radio type"; } typedef media-stream-decision-status { type enumeration { enum "rrc-decision-denied" { value 1; description "RRC decision denied"; } enum "rrc-decision-admit" { value 2; description "RRC decision admit"; } enum "rrc-decision-bad-client-denied" { value 3; description "RRC decision bad client denied"; } enum "rrc-decision-bad-client-demote" { value 4; description "RRC decision bad client demote"; } } description "Media-stream decision status"; } typedef rogue-class-type { type enumeration { enum "rogue-classtype-unknown" { value 0; description "Pending"; } enum "rogue-classtype-friendly" { value 1; description "This object specifies a known and acknowledged rogue AP"; } enum "rogue-classtype-malicious" { value 2; description "This object specifies an unknown AP that matches user defined malicious rule"; } enum "rogue-classtype-unclassified" { value 3; description "This object specifies an unknown AP that did not match any classification rule"; } enum "rogue-classtype-custom" { value 4; description "Custom"; } enum "rogue-classtype-invalid" { value 5; description "Custom"; } } description "represents the categorization of the identified rogues"; } typedef rogue-security-level { type enumeration { enum "rogue-security-level-low" { value 0; description "This object specifies the security level is low"; } enum "rogue-security-level-high" { value 1; description "This object specifies the security level is High"; } enum "rogue-security-level-critical" { value 2; description "This object specifies the security level is critical"; } enum "rogue-security-level-custom" { value 3; description "This object specifies the user can configure rogue detection parameters"; } } description "This object specifies the specifies the rogue detection security level"; } typedef rldp-config-mode { type enumeration { enum "rldp-cfg-mode-disable" { value 0; description "This object specifies that RLDP is disabled"; } enum "rldp-cfg-mode-enable" { value 1; description "This object specifies that RLDP is enabled on all APs"; } enum "rldp-cfg-mode-enable-monitor-only" { value 2; description "This object specifies that RLDP is enabled on monitor APs only"; } } status deprecated; description "This object specifies the specifies the rogue detection security level"; } typedef rogue-state { type enumeration { enum "rogue-state-init" { value 0; description "rogue state Init"; } enum "rogue-state-pending" { value 1; description "Pending"; } enum "rogue-state-alert" { value 2; description "This object specifies the Alert state means Rogue AP can be a potential threat"; } enum "rogue-state-lrad" { value 3; description "rouge state Lrad"; } enum "rogue-state-trusted" { value 4; description "This object specifies the Known state means its just internal AP which is not on the same Switch"; } enum "rogue-state-acknowledged" { value 5; description "This object specifies the Acknowledge state means an external AP whose existence is acceptable and not a threat "; } enum "rogue-state-contained" { value 6; description "This object specifies the Contained means containment is initiated and ongoing"; } enum "rogue-state-threat" { value 7; description "This object specifies the the state when the rogue is found on wired network"; } enum "rogue-state-contained-pending" { value 8; description "This object specifies the will appear in known rogue list"; } enum "rogue-state-deleted" { value 9; description "Delete"; } enum "rogue-state-invalid" { value 10; description "Invalid"; } } description "This object specifies the This attribute is used to specify the state in which the Rogue AP is"; } typedef rrm-control-mode { type enumeration { enum "rrm-automatic" { value 0; description "This object specifies the Enables auto-RF"; } enum "rrm-run-once" { value 1; description "This object specifies the Enables one-time auto-RF"; } enum "rrm-static" { value 2; description "This object specifies the Disables 802.11b RF grouping selection"; } enum "rrm-leader" { value 3; description "This object specifies the Sets the 802.11b RF group selection to leader mode"; } enum "rrm-restart" { value 4; description "RESTART"; } } description "This object specifies the indicates the mode for the RRM algorithm for the band"; } typedef preferred-mode-type { type enumeration { enum "preferred-mode-unconfig" { value 0; description "option to denote the capwap preferred mode is not configured"; } enum "preferred-mode-ipv4" { value 1; description "option to denote the capwap preferred mode is IPV4"; } enum "preferred-mode-ipv6" { value 2; description "option to denote the capwap preferred mode is IPV6"; } } description "enum to denote the capwap preferred mode type"; } typedef ipv6-capwap-checksum-type { type enumeration { enum "udplite-checksum-unconfigured" { value 0; description "UDP-Lite checksum not yet configured"; } enum "udplite-checksum-enabled" { value 1; description "UDP-Lite checksum for IPv6 CAPWAP data packets"; } enum "udplite-checksum-disabled" { value 2; description "UDP checksum for IPv6 CAPWAP data packets"; } } description "Enumeration denoting IPv6 CAPWAP data checksum type"; } typedef rad-cert-type { type enumeration { enum "ap-cert-mic" { value 1; description "This object specifies the Manufacture Installed Certificate"; } enum "ap-cert-ssc" { value 2; description "This object specifies the Self Signed Certificate type"; } enum "ap-cert-lsc" { value 3; description "This object specifies the Local Significance"; } } description "This object specifies the Enum values denoting AP Certificate Type"; } typedef apf-rogue-rule-rule-match-op { type enumeration { enum "rule-match-none" { value 0; description "This object specifies the Requires no conditions to be met for the rule to be matched"; } enum "rule-match-all" { value 1; description "This object specifies the Requires all conditions to be met for the rule to be matched"; } enum "rule-match-any" { value 2; description "This object specifies the Requires any one condition to be met for the rule to be matched"; } enum "rule-match-max" { value 3; description "Placeholder for the maximum number of rules that can match for the particular AP/client"; } } description "specifies the type of rule matching that needs to be done"; } typedef apf-vap-80211-encryption { type enumeration { enum "apf-vap-80211-encryp-wep104" { value 0; description "104-bit WEP"; } enum "apf-vap-80211-encryp-wep40" { value 1; description "40-bit WEP"; } } description "This object specifies the Type of Static WEP Encryption"; } typedef apf-vap-8021x-encryption { type enumeration { enum "apf-vap-8021x-encryp-wep104" { value 0; description "104-bit WEP"; } enum "apf-vap-8021x-encryp-none" { value 1; description "8021x Encryption None"; } enum "apf-vap-8021x-encryp-wep40" { value 2; description "40-bit WEP"; } } description "This object specifies the Type of 802.1X Encryption. This applies if bsnDot11Ess8021xSecurity is in enabled state"; } typedef apf-vap-80211-authentication { type enumeration { enum "apf-vap-80211-auth-open" { value 0; description "This object specifies the Open system authentication"; } enum "apf-vap-80211-auth-shared-key" { value 1; description "This object specifies the Shared key authentication"; } enum "apf-vap-80211-auth-wpa-8021x" { value 2; description "This object specifies the Wi-Fi Protected Access key authentication"; } enum "apf-vap-80211-auth-wpa-psk" { value 3; description "Protected System (WPA-PSK)"; } enum "apf-vap-80211-auth-cckm-8021x" { value 4; description "Protected System (CCKM+802.1X)"; } enum "apf-auth-alg-cisco-leap" { value 128; description "Protected System (Cisco LEAP)"; } } description "This object specifies the Type of 802.11 system authentication"; } typedef apf-vap-lan-sub-type { type enumeration { enum "apf-vap-wireless-lan" { value 1; description "specifies the sub-type of the LAN created."; } enum "apf-vap-guest-lan" { value 2; description "Lan subtype is guest"; } enum "apf-vap-remote-lan" { value 3; description "Lan subtype is remote lan"; } } description "This object specifies the specifies the sub-type of the LAN created"; } typedef apf-vap-radio-policies { type enumeration { enum "apf-vap-radio-all" { value 0; description "This object specifies the Configures the WLAN on all Radio bands"; } enum "apf-vap-radio-80211b-only" { value 1; description "This object specifies the Configures the WLAN on 802.11b only"; } enum "apf-vap-radio-80211a-only" { value 2; description "This object specifies the Configures the WLAN on 802.11a only"; } enum "apf-vap-radio-80211g-only" { value 3; description "This object specifies the Configures the WLAN on 802.11g only"; } enum "apf-vap-radio-80211bg-only" { value 4; description "This object specifies the Configures the WLAN on 802.11b and 802.11g only"; } enum "apf-vap-radio-80211ag-only" { value 5; description "This object specifies the Configures the WLAN on 802.11a and 802.11g only"; } enum "apf-vap-radio-80211-ab-only" { value 6; description "This object specifies the Configures the WLAN on 802.11a and 802.11b only"; } enum "apf-vap-radio-none" { value 7; description "This object specifies the Configures the Wlan to None"; } enum "apf-vap-80211b-simulated-remote-lan" { value 8; description "This object specifies the Configures the WLAN on simulated remote lan"; } } description "represents the radio policy in the wlan"; } typedef apf-vap-wme-policies { type enumeration { enum "apf-vap-wme-disabled" { value 0; description "This object specifies the disable WMM on the WLAN"; } enum "apf-vap-wme-allowed" { value 1; description "This object specifies the Allows WMM on the WLAN"; } enum "apf-vap-wme-required" { value 2; description "This object specifies the Requires WMM enabled clients on the WLAN"; } enum "apf-vap-wme-invalid" { value 3; description "This object specifies the WME is invalid clients on the WLAN"; } } description "This object specifies the When enabled, WME Policy is applied on the packets"; } typedef apf-vap-pmf-policies { type enumeration { enum "apf-vap-pmf-disabled" { value 0; description "This object specifies the Configures PMF as disabled"; } enum "apf-vap-pmf-optional" { value 1; description "This object specifies the Configures PMF as optional"; } enum "apf-vap-pmf-required" { value 2; description "This object specifies the Configures PMF as mandatory"; } } description "This object specifies the specifies the 802.11w PFM configuration for a particular WLAN"; } typedef apf-vap-auto-qos-profile { type enumeration { enum "apf-vap-auto-qos-disabled" { value 0; description "unknown"; } enum "apf-vap-auto-qos-enterprise" { value 1; description "This object specifies the Enable AutoQos Wireless Enterprise Policy"; } enum "apf-vap-auto-qos-voice" { value 2; description "This object specifies the Enabling Auto QoS Voice will enable call-snooping and voice acm"; } enum "apf-vap-auto-qos-guest" { value 3; description "This object specifies the Enable AutoQoS Wireless Guest Policy"; } } description "Enumeration specifies the group of auto QoS profile"; } typedef apf-vap-wifi-direct-policies { type enumeration { enum "apf-vap-wifidirect-disable" { value 0; description " WFD is completely disabled"; } enum "apf-vap-wifidirect-allowed" { value 1; description "This object specifies the Allow all the wifi direct clients to associate unconditionally"; } enum "apf-vap-wifidirect-not-allowed" { value 2; description "This object specifies the Disallow wifi direct clients with concurrency enabled to associate with WLAN"; } enum "apf-vap-wifidirect-invalid" { value 3; description "Invalid wifi direct policy"; } enum "apf-vap-wifidirect-not-allowed-xc" { value 4; description "This object specifies the Disallow wifi direct clients that provide cross-connect capability to associate"; } } description "This object specifies the is used to allow/disallow wi-fi direct clients to/from joining the infrastructure network"; } typedef mm-secure-cipher-list { type enumeration { enum "mm-secure-cipher-disable" { value 0; description "This object specifies the A value of 'disable' implies that controllers will continue to use default ciphers for Mobility tunnel"; } enum "mm-secure-cipher-aes256-sha" { value 1; description "This object specifies the A value of 'aes256sha1' implies that controllers will use AES256_SHA cipher for Mobility tunnel"; } enum "mm-secure-cipher-aes256-sha256" { value 2; description "This object specifies the A value of 'aes256sha2' implies that controllers will use AES256_SHA256 cipher for Mobility tunnel"; } } description "This object specifies the This object is used to configure secure ciphers, AES256+SHA or AES256+SHA2 for Mobility tunnel"; } typedef mfp-event { type enumeration { enum "mfp-event-invalid-mic" { value 0; description "Invalid MIC"; } enum "mfp-event-invalid-seq" { value 1; description "Invalid Sequence"; } enum "mfp-event-no-mic" { value 2; description "No MIC"; } enum "mfp-event-unexpected-mic" { value 3; description "Unexpected MIC"; } } description "MFP event types"; } typedef apf-80211-qos-mode { type enumeration { enum "apf-80211-qos-mode-default-wmm" { value 1; description "This object specifies the Enable WMM default parameters for 802.11b"; } enum "apf-80211-qos-mode-spectralink" { value 2; description "This object specifies the Enable SpectraLink Voice Priority parameters for 802.11b"; } enum "apf-80211-qos-mode-optimized-voice" { value 3; description "This object specifies the Enable non-spectralink voice-optimized parameters for 802.11b"; } enum "apf-80211-qos-mode-optimized-voice-video" { value 4; description "This object specifies the Enable combined video-voice-optimized parameters for 802.11b"; } enum "apf-80211-qos-mode-custom-voice" { value 5; description "This object specifies the Enable Custom Voice parameters for 802.11b"; } enum "apf-80211-qos-mode-custom" { value 6; description "custom"; } enum "apf-80211-qos-mode-invalid" { value 7; description "Invalid"; } } description "This object specifies the This object specifies the EDCA profile to be used in EDCA Parameter set element"; } typedef radio-type { type enumeration { enum "dot11-invalid-value" { value 0; description "Invalid"; } enum "dot11-2-dot-4-ghz" { value 1; description "2.4 GHz"; } enum "dot11-5-ghz" { value 2; description "5 GHz"; } enum "dot11-dualband-radio" { value 3; description "Dual Band"; } enum "dot11-4-dot-9-ghz" { value 4; description "4.9 GHz"; } enum "dot11-5-dot-8-ghz" { value 5; description "5.8 GHz"; } enum "dot11-6-ghz" { value 6; description "6 GHz"; } } description "This object specifies the this represents various radio band type"; } typedef enm-radio-band { type enumeration { enum "band-2-dot-4-ghz" { value 1; description "Radio band - 2.4 GHz"; } enum "band-5-ghz" { value 2; description "Radio band - 5 GHz"; } enum "band-dualband-radio" { value 3; description "Radio band - dual band"; } enum "band-6-ghz" { value 4; description "Radio band - 6 GHz"; } } description "Enumeration for 802.11 radio band"; } typedef slot-id-type { type enumeration { enum "slot-0" { value 0; description "slot 0"; } enum "slot-1" { value 1; description "slot 1"; } enum "slot-2" { value 2; description "slot 2"; } enum "slot-3" { value 3; description "slot 3"; } } description "This object specifies the This subtype represents a various Slot Id type of an AP"; } typedef half-life-time { type enumeration { enum "half-life-time-0" { value 0; description "This object specifies the A value of 0 indicates that timeout is disabled"; } enum "half-life-time-1" { value 1; description "slot 1"; } enum "half-life-time-2" { value 2; description "slot 2"; } enum "half-life-time-5" { value 5; description "slot 5"; } enum "half-life-time-10" { value 10; description "half time is 10"; } enum "half-life-time-20" { value 20; description "half time is 20"; } enum "half-life-time-30" { value 30; description "half time is 30"; } enum "half-life-time-60" { value 60; description "half time is 60"; } enum "half-life-time-90" { value 90; description "half time is 90"; } enum "half-life-time-120" { value 120; description "half time is 120"; } enum "half-life-time-180" { value 180; description "half time is 180"; } enum "half-life-time-300" { value 300; description "half time is 300"; } } description "This object specifies the This object specifies the half-life timeout for the client"; } typedef ap-eth-port-speed { type enumeration { enum "ap-ethernet-port-speed-auto" { value 0; description "This object specifies the this subtype represents ethernet port speed with auto adjustable"; } enum "ap-ethernet-port-speed-10-mbps" { value 1; description "This object specifies the this subtype represents ethernet port speed with speed of 10 Mbps"; } enum "ap-ethernet-port-speed-100-mbps" { value 2; description "This object specifies the this subtype represents ethernet port speed with speed of 100 mbps"; } enum "ap-ethernet-port-speed-1000-mbps" { value 3; description "This object specifies the this subtype represents ethernet port speed with speed of 1000 mbps"; } enum "ap-ethernet-port-speed-2500-mbps" { value 4; description "This object specifies the this subtype represents ethernet port speed with speed of 2500 mbps"; } enum "ap-ethernet-port-speed-5000-mbps" { value 5; description "This object specifies the this subtype represents ethernet port speed with speed of 5000 mbps"; } enum "ap-ethernet-port-speed-invalid" { value 6; description "Ethernet port speed is invalid"; } } description "This object specifies the this subtype represents ethernet port speed"; } typedef ap-eth-port-duplex { type enumeration { enum "ap-ethernet-port-duplex-auto" { value 0; description "ethernet port duplex Auto"; } enum "ap-ethernet-port-duplex-half" { value 1; description "ethernet port duplex Half"; } enum "ap-ethernet-port-duplex-full" { value 2; description "ethernet port duplex Full"; } } description "enumeration for mode of the ethernet port"; } typedef memory-core-dump-flag { type enumeration { enum "tftp-coredump-uncompress" { value 0; description "This object specifies the Do not compress the core dump file"; } enum "tftp-coredump-compress" { value 1; description "This object specifies the Compress the core dump file"; } enum "tftp-coredump-disable" { value 2; description "This object specifies the disable the core dump file"; } } description "enumeration listing the treatment to the coredump generated at the AP"; } typedef rate-state { type enumeration { enum "apf-tx-rate-unsupported" { value 0; description "This object specifies the Disables a rate"; } enum "apf-tx-rate-supported" { value 1; description "This object specifies the Configures a rate to supported"; } enum "apf-tx-rate-basic" { value 2; description "This object specifies the Configures a rate to mandatory"; } enum "apf-tx-rate-not-applicable" { value 3; description "Not applicable"; } } description "enumeration listing the type of Tx rate supported"; } typedef apf-80211n-amsdu { type enumeration { enum "apf-80211n-amsdu-disable" { value 0; description " 80211N AMSDU is disabled"; } enum "apf-80211n-amsdu-enable" { value 1; description "80211N AMSDU is enabled"; } enum "apf-80211n-amsdu-invalid" { value 2; description "80211N AMSDU is invalid"; } } description "Specifies the 80211n aggregation msd unit"; } typedef apf-80211n-ampdu { type enumeration { enum "apf-80211n-ampdu-disable" { value 0; description "80211N AMPDU is disabled"; } enum "apf-80211n-ampdu-enabled" { value 1; description "80211N AMPDU enabled"; } enum "apf-80211n-ampdu-invalid" { value 2; description "80211N AMPDU is invalid"; } } description "80211n AMPDU is present"; } typedef ndp-type { type enumeration { enum "ndp-type-transparent" { value 0; description "NDP type is Transparent"; } enum "ndp-type-protected" { value 1; description "NDP type is Protected"; } } description "Enum for NDP type"; } typedef rrm-group-member { type enumeration { enum "group-member-noaction" { value 0; description "No-operation on the Rrm group member"; } enum "group-member-add" { value 1; description "Operation representing Rrm group member to be added"; } enum "group-member-delete" { value 2; description "Operation representing Rrm group member to be deleted"; } } description "enumeration listing the operation on the RRM group member"; } typedef datarate { type enumeration { enum "optroam-rate-1-m" { value 1; description "1 Mbps data rate threshold"; } enum "optroam-rate-2-m" { value 2; description "2 Mbps data rate threshold"; } enum "optroam-rate-5-5-m" { value 5; description "5 Mbps data rate threshold"; } enum "optroam-rate-6-m" { value 6; description "6 Mbps data rate threshold"; } enum "optroam-rate-9-m" { value 9; description "9 Mbps data rate threshold"; } enum "optroam-rate-11-m" { value 11; description "11 Mbps data rate threshold"; } enum "optroam-rate-12-m" { value 12; description "12 Mbps data rate threshold"; } enum "optroam-rate-18-m" { value 18; description "18 Mbps data rate threshold"; } enum "optroam-rate-24-m" { value 24; description "24 Mbps data rate threshold"; } enum "optroam-rate-36-m" { value 36; description "36 Mbps data rate threshold"; } enum "optroam-rate-48-m" { value 48; description "48 Mbps data rate threshold"; } enum "optroam-rate-54-m" { value 54; description "54 Mbps data rate threshold"; } enum "optroam-rate-0" { value 0; description "0 Mbps data rate threshold"; } } description "Enum for data rate threshold of 802.11 Optimized Roaming"; } typedef dca-threshold { type enumeration { enum "dca-threshold-low" { value 0; description "Low DCA sensitivity level"; } enum "dca-threshold-medium" { value 1; description "Medium DCA sensitivity level"; } enum "dca-threshold-high" { value 2; description "High DCA sensitivity level"; } } description "Enum for DCA sensitivity levels"; } typedef apf-location-algorithm-type { type enumeration { enum "loc-alg-simple" { value 1; description "This object specifies the A faster algorithm with smaller CPU overhead but less accuracy"; } enum "loc-alg-average" { value 2; description "This object specifies the A more accurate algorithm but with more CPU overhead"; } } description "This object specifies the this represents algorithm type and CPU overhead"; } typedef ant-band-mode { type enumeration { enum "ant-band-mode-unknown" { value 1; description "antenna mode unknown"; } enum "ant-band-mode-single" { value 2; description "This object specifies the antenna is operating in single band"; } enum "ant-band-mode-dual" { value 3; description "This object specifies the antenna is operating in dual band"; } } description "This object specifies the This object specifies the mode of Antenna band"; } typedef power-injector-state { type enumeration { enum "pwrinj-state-disable" { value 0; description "Disable one radio for ither to receive full power"; } enum "pwrinj-state-specify-mac" { value 1; description "Specify the mac address of the connected switch port used as power injector"; } enum "pwrinj-state-override-mac" { value 66; description "Override the mac address of the connected switch port used as power injector"; } enum "pwrinj-state-unsupported" { value 68; description "Power injector state is not supported for the particular AP"; } } description "List all the types of power injector modes/options"; } typedef power-injector-selection { type enumeration { enum "pwrinj-selection-unknown" { value 1; description "mode of the power injector selection is unknown"; } enum "pwrinj-selection-installed" { value 2; description "This object specifies the configure the MAC address of the switch port that has a Power Injector"; } enum "pwrinj-selection-override" { value 3; description "This object specifies the override the safety checks and assume a Power Injector is always installed."; } } description "This object specifies the This object specifies the Power Injector selection value of the AP"; } typedef apf-qos-def-pm-create-status { type enumeration { enum "qos-def-pm-status-none" { value 0; description "QOS def PM status none"; } enum "qos-def-pm-status-created" { value 1; description "QOS def PM status created"; } enum "qos-def-pm-status-valid-pending" { value 2; description "QOS def PM status valid pending"; } enum "qos-def-pm-status-valid-requested" { value 3; description "QOS def PM status valid requested"; } enum "qos-def-pm-status-valid-failed" { value 4; description "QOS def PM status valid failed"; } enum "qos-def-pm-status-valid-success" { value 5; description "QOS def PM status valid success"; } enum "qos-def-pm-status-install-requested" { value 6; description "QOS def PM status install requested"; } enum "qos-def-pm-status-install-failed" { value 7; description "QOS def PM status install failed"; } enum "qos-def-pm-status-install-success" { value 8; description "QOS def PM status install success"; } enum "qos-def-pm-status-max" { value 9; description "QOS def PM status max"; } } description "QOS def PM create status"; } typedef work-day { type enumeration { enum "monday" { value 1; description "Configures Monday as the day for rldp scheduling"; } enum "tuesday" { value 2; description "Configures Tuesday as the day for rldp scheduling"; } enum "wednesday" { value 3; description "Configures Wednesday as the day for rldp scheduling"; } enum "thursday" { value 4; description "Configures Thursday as the day for rldp scheduling"; } enum "friday" { value 5; description "Configures Friday as the day for rldp scheduling"; } enum "saturday" { value 6; description "Configures Saturday as the day for rldp scheduling"; } enum "sunday" { value 7; description "Configures Sunday as the day for rldp scheduling"; } } status deprecated; description "Lists all the days when rldp can be scheduled"; } typedef crypt-type { type enumeration { enum "clear" { value 0; description "This is to indicate the string encryption type is clear"; } enum "sha" { value 4; description "This is to indicate the string encryption of type SHA"; } enum "md5" { value 5; description "This is to indicate the string encryption of type MD5"; } enum "ike-aes" { value 6; description "This is to indicate the string encryption of type IKE-AES"; } enum "type7" { value 7; description "This is to indicate the string encryption of type-7"; } enum "aes" { value 8; description "This is to indicate the string encryption of type AES"; } enum "clear-to-sha" { value 40; description "This is to indicate the string encryption of type Clear to SHA"; } enum "clear-to-md5" { value 50; description "This is to indicate the string encryption of type clear to MD5"; } enum "clear-to-ike-aes" { value 60; description "This is to indicate the string encryption of type clear to IKE-AES"; } enum "clear-to-type7" { value 70; description "This is to indicate the string encryption of type clear to type-7"; } enum "clear-to-aes" { value 80; description "This is to indicate the string encryption of type clear to AES"; } } description "This object specifies the This is to indicate the string encryption type"; } typedef lomm-mode-type { type enumeration { enum "mode-type-all" { value 1; description "This object specifies the All optimization is enabled"; } enum "tracking" { value 2; description "This object specifies the Tracking is optimized"; } enum "wips" { value 3; description "This object specifies the WIPS optimization is enabled"; } enum "mode-type-none" { value 4; description "Default"; } } description "This object specifies the This object represents the monitor mode optimization on this device"; } typedef dot11-min-phy-rate { type enumeration { enum "one" { value 1; description "Phy rate is 1000"; } enum "two" { value 2; description "Phy rate is 2000"; } enum "five-point-five" { value 5; description "Phy rate is 5500"; } enum "six" { value 6; description "Phy rate is 6000"; } enum "nine" { value 9; description "Phy rate is 9000"; } enum "eleven" { value 11; description "Phy rate is 11000"; } enum "twelve" { value 12; description "Phy rate is 1200"; } enum "eighteen" { value 18; description "Phy rate is 18000"; } enum "twenty-four" { value 24; description "Phy rate is 24000"; } enum "thirty-six" { value 36; description "Phy rate is 36000"; } enum "forty-eight" { value 48; description "Phy rate is 48000"; } enum "fifty-four" { value 54; description "Phy rate is 54000"; } enum "sixty-five" { value 65; description "Phy rate is 65000"; } enum "seventy-two-point-two" { value 72; description "Phy rate is 72200"; } enum "one-thirty" { value 130; description "Phy rate is 13000"; } enum "one-thirty-five" { value 135; description "Phy rate is 13500"; } enum "one-forty-four-point-four" { value 144; description "Phy rate is 144400"; } enum "one-fifty" { value 150; description "Phy rate is 150000"; } enum "two-seventy" { value 270; description "Phy rate is 270000"; } enum "three-hundred" { value 300; description "Phy rate is 300000"; } } description "This object specifies the This object specifies the minimum physical rate that should be enabled by a client to successfully join a media stream"; } typedef power-mode-type { type enumeration { enum "dot11-default-low-pwr" { value 0; description "This object specifies the The AP is drawing default power from Ethernet"; } enum "dot11-set-low-pwr" { value 1; description "This object specifies the The AP is drawing low power from Ethernet"; } enum "dot11-set-15-4-pwr" { value 2; description "This object specifies the The AP is drawing 15.4 watts from Ethernet"; } enum "dot11-set-16-8-pwr" { value 3; description "This object specifies the The AP is drawing 16.8 watts from Ethernet"; } enum "dot11-set-high-pwr" { value 4; description "This object specifies the The AP is drawing high power from Ethernet"; } enum "dot11-default-high-pwr" { value 5; description "Power mode type is high"; } enum "dot11-set-no-pwr" { value 6; description "This object specifies the The AP is drawing no power from ethernet"; } enum "dot11-set-25-5-pwr" { value 7; description "This object specifies the The AP is drawing 25.5 watts from Ethernet"; } enum "unknown-pwr" { value 255; description "unknown power mode type"; } } description "This object specifies the This object represents the power status of the AP"; } typedef power-type { type enumeration { enum "pwr-src-brick-old" { value 0; description "AP uses a local brick style power supply"; } enum "pwr-src-brick-new" { value 1; description "AP uses a local new brick style power supply"; } enum "pwr-src-inj" { value 2; description "uses power injector for power supply"; } enum "pwr-src-poe-lgcy" { value 3; description "AP uses legacy POE mechanism"; } enum "pwr-src-poe-plus" { value 4; description "AP uses advanced POE mechanism"; } enum "pwr-src-unknown" { value 255; description "AP's power source is known"; } } description "lists all the supported power mode types"; } typedef controller-index { type enumeration { enum "controller-index-primary" { value 0; description "Primary controller index"; } enum "controller-index-secondary" { value 1; description "Secondary controller index"; } enum "controller-index-tertiary" { value 2; description "Tertiary controller index"; } enum "controller-index-max" { value 3; description "Maximum controller index"; } } description "Controller index"; } typedef enm-controller-index { type enumeration { enum "index-primary" { value 0; description "Controller will be the primary controller for an AP"; } enum "index-secondary" { value 1; description "Controller will be the secondary controller for an AP"; } enum "index-tertiary" { value 2; description "Controller will be the tertiary controller for an AP"; } } description "Enumeration specifying controller index for an AP"; } typedef rrm-ed-threshold-level { type enumeration { enum "rrm-cleanair-event-low" { value 1; description "This object specifies the low level event driven RRM threshold value"; } enum "rrm-cleanair-event-medium" { value 2; description "This object specifies the medium level event driven RRM threshold value"; } enum "rrm-cleanair-event-high" { value 3; description "This object specifies the high level event driven RRM threshold value"; } enum "rrm-cleanair-event-custom" { value 4; description "This object specifies the user specified value of even driven RRM threshold"; } } description "This object specifies the This object represents the event driven RRM threshold level"; } typedef apf-vap-key-type { type enumeration { enum "key-ascii" { value 0; description "Represents that the PSK key is specified in ascii"; } enum "key-hex" { value 1; description "Represents that the PSK key specified in hex"; } enum "key-invalid" { value 2; description "Represents that the PSK key format type is invalid"; } } description "List all the types of key specified for PSK"; } typedef spam-ap-modes { type enumeration { enum "spam-ap-mode-local" { value 0; description "This object specifies the wireless local mode"; } enum "spam-ap-mode-monitor" { value 1; description " wireless monitor mode "; } enum "spam-ap-mode-remote" { value 2; description "This object specifies the wireless remote mode"; } enum "spam-ap-mode-rogue-detector" { value 3; description "This object specifies the wireless rogue detector mode"; } enum "spam-ap-mode-sniffer" { value 4; description "This object specifies the wireless sniffer mode"; } enum "spam-ap-mode-bridge" { value 5; description "This object specifies the wireless mode bride"; } enum "spam-ap-mode-seconnect" { value 6; description "This object specifies the Spectrum Expert Only Connect mode"; } enum "spam-ap-mode-hybrid-remote" { value 7; description "This object specifies the Hybrid Remode Edge AP (H-REAP) mode"; } enum "spam-ap-mode-sensor" { value 8; description "Sensor"; } enum "spam-ap-mode-remote-bridge" { value 9; description "Not supported - Is used for mesh"; } } description "This object specifies the Monitor Only Mode Setting"; } typedef rrm-dca-chan-width { type enumeration { enum "rrm-dca-chan-width-20-mhz" { value 0; description "Channel RF Width 20 MZ"; } enum "rrm-dca-chan-width-40-mhz" { value 1; description "Channel RF Width 40 MZ"; } enum "rrm-dca-chan-width-80-mhz" { value 2; description "Channel RF Width 80 MZ"; } enum "rrm-dca-chan-width-best" { value 3; description "Channel RF Width best"; } } description "This object specifies the this object specifies how the system performs DCA channel width selection"; } typedef dca-chan-width { type enumeration { enum "dca-chan-width-20-mhz" { value 0; description "20 Mhz"; } enum "dca-chan-width-40-mhz" { value 1; description "40 Mhz"; } enum "dca-chan-width-80-mhz" { value 2; description "80 Mhz"; } enum "dca-chan-width-best" { value 3; description "best chan width"; } enum "dca-chan-width-160-mhz" { value 4; description "160 Mhz"; } enum "dca-chan-width-8080-mhz" { value 5; description "8080 Mhz"; } } description "enumeration describing channel width"; } typedef rrm-dca-chan-width-cap { type enumeration { enum "rrm-dca-chan-width-cap-20-mhz" { value 0; description "This object specifies the Chan Width 20 Mhz"; } enum "rrm-dca-chan-width-cap-40-mhz" { value 1; description "This object specifies the Chan Width 40 Mhz"; } enum "rrm-dca-chan-width-cap-80-mhz" { value 2; description "This object specifies the Chan Width 80 Mhz"; } enum "rrm-dca-chan-width-cap-best" { value 3; description "This object specifies the Chan Width best"; } enum "rrm-dca-chan-width-cap-160-mhz" { value 4; description "This object specifies the Chan Width 160"; } enum "rrm-dca-chan-width-cap-max" { value 5; description "This object specifies the Chan Width max"; } } description "This object specifies the config 802.11a dynamic channel assignment algorithm parameters"; } typedef dca-chan-width-cap { type enumeration { enum "dca-chan-width-cap-20-mhz" { value 0; description "20 MHz"; } enum "dca-chan-width-cap-40-mhz" { value 1; description "40 MHz"; } enum "dca-chan-width-cap-80-mhz" { value 2; description "80 MHz"; } enum "dca-chan-width-cap-best" { value 3; description "best chan width"; } enum "dca-chan-width-cap-160-mhz" { value 4; description "160 Mhz"; } enum "dca-chan-width-cap-max" { value 5; description "MAX ALLOWED"; } } description "enumeration describing channel width"; } typedef rf-rrm-dca-chan-width { type enumeration { enum "rf-rrm-dca-chan-width-20-mhz" { value 0; description "This object specifies the 20 MHz channel width supported by this radio"; } enum "rf-rrm-dca-chan-width-40-mhz" { value 1; description "This object specifies the 40 MHz channel width supported by this radio"; } enum "rf-rrm-dca-chan-width-80-mhz" { value 2; description "This object specifies the 80 MHz channel width supported by this radio"; } enum "rf-rrm-dca-chan-width-best" { value 3; description "This object specifies the Dynamic channel width(160 MHz, 80 MHz, 40 MHz or 20 MHz) supported by this radio"; } } description "This object specifies the This object specifies how the system performs DCA channel width selection for the RFProfile"; } typedef rf-dca-chan-width { type enumeration { enum "rf-dca-chan-width-20-mhz" { value 0; description "20 MHz"; } enum "rf-dca-chan-width-40-mhz" { value 1; description "40 MHz"; } enum "rf-dca-chan-width-80-mhz" { value 2; description "80 MHz"; } enum "rf-dca-chan-width-best" { value 3; description "best chan width"; } enum "rf-dca-chan-width-160-mhz" { value 4; description "160 MHz"; } enum "rf-dca-chan-width-8080-mhz" { value 5; description "80+80 MHz"; } } description "enumeration describing channel width"; } typedef channel-monitor-mode { type enumeration { enum "rrm-channels-country" { value 1; description "This object specifies the Monitor channels used in configured country code"; } enum "rrm-channels-all" { value 2; description "This object specifies the Monitor all channels"; } enum "rrm-channels-dca" { value 3; description "This object specifies the Monitor channels used by dynamic channel assignment"; } } description "This object specifies the Sets the noise/interference/rogue monitoring channel-list"; } typedef nw-leg-beam-form { type enumeration { enum "nw-leg-bf-disable" { value 0; description "This object specifies the Disable 802.11b tx beamforming - 2.4 GHz"; } enum "nw-leg-bf-enable" { value 1; description "This object specifies the Enable 802.11b tx beamforming - 2.4 GHz"; } enum "nw-leg-bf-na" { value 2; description "This object specifies the beamforming is not applicable"; } } description "Enables/disables beam forming on 11g"; } typedef admin-state { type enumeration { enum "adminstate-enabled" { value 1; description "This object specifies the A value of 'true' enables the Admin State"; } enum "adminstate-disabled" { value 2; description "This object specifies the A value of 'false' disables the Admin State"; } } description "This object specifies the This object specifies the Admin State of the AP"; } typedef ap-role { type enumeration { enum "role-normal" { value 0; description "Normal"; } enum "role-root" { value 1; description "Root AP"; } enum "role-mesh" { value 2; description "Mesh AP"; } } description "Lists all the roles of AP for the case of mesh"; } typedef cdp-cache-duplex { type enumeration { enum "cdp-cache-duplex-unknown" { value 1; description "This object specifies the The value unknown(1) indicates no duplex mode field (TLV) was reported in the most recent CDP message or the neighboring device is not connected to the AP though ethernet interface"; } enum "cdp-cache-duplex-full" { value 2; description "CDP cache duplex Full"; } enum "cdp-cache-duplex-half" { value 3; description "CDP cache duplex Half"; } } description "This object specifies the this object denotes the duplex mode of the Ethernet interface between the AP and it's neighboring CDP device, as reported in the most recent CDP message"; } typedef console-login-status { type enumeration { enum "login-status-success" { value 1; description "Success"; } enum "login-status-failure" { value 2; description "Failure"; } enum "login-status-logoff" { value 3; description "Logoff"; } enum "login-status-timeout" { value 4; description "Timeout"; } } description "Lists the result of operation to dump logs on the AP console"; } typedef enm-antenna-selection { type enumeration { enum "antenna-side-a" { value 0; description "Antenna side A"; } enum "antenna-side-b" { value 1; description "Antenna side B"; } enum "antenna-diversity-enabled" { value 255; description "Antenna Diversity enabled"; } } description "Enum for Antenna Selection"; } typedef slot-radio-sub-band { type enumeration { enum "radio-sub-band-all" { value 1; description "All(SLOT_RADIO_SUB_BAND_ALL)"; } enum "4-dot-9-ghz" { value 2; description "4.9 GHz"; } enum "5-dot-2-ghz" { value 3; description "5.2 GHz"; } enum "5-dot-4-ghz" { value 4; description "5.4 GHz"; } enum "5-dot-8-ghz" { value 5; description "5.8 GHz"; } } description "This object specifies the This object indicates the sub band on which this radio operates"; } typedef oper-state { type enumeration { enum "oper-state-up" { value 1; description "oper state is UP"; } enum "oper-state-down" { value 2; description "oper state is DOWN"; } enum "oper-state-na" { value 3; description "Not available"; } } description "This object specifies the This object represents the operational state of the physical Ethernet interface on the AP"; } typedef enm-antenna-mode { type enumeration { enum "antenna-mode-sector-a" { value 1; description "Antenna mode sector A"; } enum "antenna-mode-sector-b" { value 2; description "Antenna mode sector B"; } enum "antenna-mode-omni" { value 3; description "Antenna mode omni"; } enum "antenna-mode-mimo" { value 4; description "Antenna mode mimo"; } } description "Enum for Antenna Mode"; } typedef frame-burst-mode { type enumeration { enum "frame-burst-automatic" { value 0; description "This object specifies the Use optimal settings for bursting of 802.11ac A-MPDUs"; } enum "frame-burst-enabled" { value 1; description "Enabled"; } enum "frame-burst-disabled" { value 2; description "Disabled"; } } description "This object specifies the Configure 802.11ac Frame Burst"; } typedef enm-lan-port-id { type enumeration { enum "port-id-1" { value 1; description "Port ID 1"; } enum "port-id-2" { value 2; description "Port ID 2"; } enum "port-id-3" { value 3; description "Port ID 3"; } enum "port-id-4" { value 4; description "Port ID 4"; } } description "Enumeration for AP LAN port ID"; } typedef rx-sen-sop-threshold-level { type enumeration { enum "rrm-rxsensop-threshold-auto" { value 0; description "rrm rx sensitivity threshold is auto"; } enum "rrm-rxsensop-threshold-low" { value 1; description "low (-80 dbm)"; } enum "rrm-rxsensop-threshold-medium" { value 2; description "medium (-78 dbm)"; } enum "rrm-rxsensop-threshold-high" { value 3; description "high (-76 dbm)"; } } description "rx sensitivity threshold level"; } typedef apf-ate-mode { type enumeration { enum "apf-atf-mode-disable" { value 0; description "Disable"; } enum "apf-atf-mode-ssid" { value 1; description "This object specifies the Configure airtime-fairness in enforce-policy mode"; } enum "apf-atf-mode-monitor" { value 2; description "This object specifies the Monitor Mode represented by cLApDot11IfType of ATF supported APs joined in the controller"; } } description "This object specifies the This object is used to set the airtime-fairness mode"; } typedef apf-ate-stealing-policy { type enumeration { enum "apf-atf-stealing-policy-disable" { value 0; description "This object specifies the Disable airtime-fairness optimization"; } enum "apf-atf-stealing-policy-enable" { value 1; description "This object specifies the Enable airtime-fairness optimization"; } } description "This object specifies the This object is used to configure the Optimization Policy represented by cLApDot11IfType of ATF supported APs, joined in the controller"; } typedef edca-profile { type enumeration { enum "edca-wmm" { value 1; description "default-wmm"; } enum "edca-spectralink-voice-priority" { value 2; description "This object specifies the Enable SpectraLink Voice Priority parameters for 802.11b"; } enum "edca-voice-optimized" { value 3; description "This object specifies the Enable non-spectralink voice-optimized parameters for 802.11b"; } enum "edca-video-voice-optimized" { value 4; description "This object specifies the Enable combined video-voice-optimized parameters for 802.11b"; } enum "edca-custom-voice" { value 5; description "This object specifies the Enable Custom Voice parameters for 802.11b"; } enum "edca-custom" { value 6; description "custom"; } enum "edca-fastlane" { value 7; description "This object specifies the Enable Fastlane parameters for 802.11b"; } enum "edca-invalid" { value 8; description "Specifies the Enhanced Distribution is invalid"; } } description "This object specifies the Configure 802.11b EDCA (Enhanced Distributed Channel Access) parameters"; } typedef autoqos-profile { type enumeration { enum "autoqos-disabled" { value 0; description "This object specifies the Disable of AutoQos Wireless Enterprise Policy"; } enum "autoqos-enterprise" { value 1; description "This object specifies the Enable AutoQos Wireless Enterprise Policy"; } enum "autoqos-voice" { value 2; description "This object specifies the Enabling Auto QoS Voice will enable call-snooping"; } enum "autoqos-guest" { value 3; description "This object specifies the Enable AutoQos Wireless Guest Policy"; } enum "autoqos-fastlane" { value 4; description "This object specifies the Enable AutoQos Wireless Fastlane Policy"; } } description "Enumeration Specifies the group of Auto qos profile"; } typedef eap-method-type { type enumeration { enum "eap-type-none" { value 0; description "EAP-None"; } enum "eap-type-md5" { value 4; description "EAP-MD5"; } enum "eap-type-eap-tls" { value 13; description "EAP-TLS"; } enum "eap-type-leap" { value 17; description "EAP-LEAP"; } enum "eap-type-sim" { value 18; description "EAP-SIM"; } enum "eap-type-ttls" { value 21; description "EAP-TTLS"; } enum "eap-type-aka" { value 23; description "EAP-AKA"; } enum "eap-type-peap" { value 25; description "EAP-PEAP"; } enum "eap-type-speke" { value 41; description "SPEKE"; } enum "eap-type-eap-fast" { value 43; description "EAP-FAST"; } } description "Lists all supported EAP types in the device"; } typedef enm-apf-xor-roam-probe-suppression { type enumeration { enum "apf-xor-suppress-opmode-disabled" { value 0; description "Disabled"; } enum "apf-xor-suppress-opmode-probe-suppress" { value 1; description "This object specifies the Enables mode to suppress only probes"; } enum "apf-xor-suppress-opmode-authprobe-suppress" { value 2; description "This object specifies the Enables mode to suppress probes and single auth"; } enum "apf-xor-suppress-opmode-invalid" { value 3; description "Invalid"; } } description "This object specifies the Configures micro-Macro probe suppression arguments"; } typedef rogue-rldp-result { type enumeration { enum "rogue-rldp-none" { value 0; description "Unknown rldp result"; } enum "rogue-rldp-no-rogue" { value 1; description "This object specifies the Rogue not found in DB"; } enum "rogue-rldp-managed-ap" { value 2; description "This object specifies the Trying to run RLDP on a managed AP"; } enum "rogue-rldp-friendly" { value 3; description "This object specifies the Trying to run RLDP on a friendly rogue"; } enum "rogue-rldp-no-ap" { value 4; description "This object specifies the No AP found to run RLDP"; } enum "rogue-rldp-ap-in-use" { value 5; description "This object specifies the The selected AP is already in use for another RLDP"; } enum "rogue-rldp-already-in-progress" { value 6; description "This object specifies the RLDP is already in progress on this rogue"; } enum "rogue-rldp-encr-enabled" { value 7; description "This object specifies the Rogue is using an encrypted SSID"; } enum "rogue-rldp-no-ssid" { value 8; description "This object specifies the The SSID of the rogue is hidden"; } enum "rogue-rldp-ssid-too-long" { value 9; description "This object specifies the The SSID name of the rogue is too long"; } enum "rogue-rldp-state-changed-auto" { value 10; description "This object specifies the Rogue state changed because of autocontainment"; } enum "rogue-rldp-auth-timeout" { value 11; description "This object specifies the Auth failed"; } enum "rogue-rldp-assoc-timeout" { value 12; description "This object specifies the association timeout"; } enum "rogue-rldp-dhcp-timeout" { value 13; description "This object specifies the DHCP failed"; } enum "rogue-rldp-not-connected" { value 14; description "This object specifies the Special case for UDP timeout"; } enum "rogue-rldp-connected" { value 15; description "This object specifies the the rogue AP is connected to our network"; } enum "rogue-rldp-error" { value 16; description "This object specifies the the generic error occured"; } } status deprecated; description "Lists all possible results of the rldp operation"; } typedef ft-dot11r-mode { type enumeration { enum "dot11r-disabled" { value 0; description "FT mode is 11r disabled"; } enum "dot11r-enabled" { value 1; description "FT mode is 11r enabled"; } enum "dot11r-adaptive-enabled" { value 2; description "This object specifies the Configures Fast Transition Adaptive support"; } } description "This object specifies the This object specifies the 802.11r Fast Transition Mode"; } typedef ap-misconfig-state { type enumeration { enum "not-misconfigured" { value 0; description "Profile-tag is not misconfigured"; } enum "misconfigured" { value 1; description "Profile-tag is misconfigured"; } } description "Enum for profile-tag misconfigure state"; } typedef ap-tag-register-state { type enumeration { enum "ap-tag-reg-not-done" { value 0; description "AP tag registration is not done"; } enum "ap-tag-reg-done" { value 1; description "AP tag registration is done"; } } description "Enum for ap tag registration"; } typedef enm-export-anchor-priority-type { type enumeration { enum "export-anchor-primary" { value 1; description "export anchor primary"; } enum "export-anchor-secondary" { value 2; description "export anchor secondary"; } enum "export-anchor-tertiary" { value 3; description "export anchor tertiary"; } } description "Enum for export anchor priority"; } typedef ewlc-guest-lan-has-wired-vlan { type enumeration { enum "ewlc-guest-lan-without-wired-vlan" { value 1; description "Value indicating Guest Anchor"; } enum "ewlc-guest-lan-with-wired-vlan" { value 2; description "Value indicating Guest Foreign"; } } description "Enum for Wired Guest controller parameter has_wired_vlan"; } typedef client-type { type enumeration { enum "tspec-client" { value 1; description "TSPEC voice client type"; } enum "sip-client" { value 2; description "SIP voice client"; } } description "Enum for voice client type"; } typedef eogre-client-match-reason { type enumeration { enum "match-pending-classify" { value 0; description "client pending classification"; } enum "match-simple-client" { value 1; description "simple client"; } enum "match-eogre-client-rule" { value 2; description "EoGRE client matching profile"; } enum "match-eogre-client-aaa-override" { value 3; description "EoGRE client with aaa data"; } enum "match-eogre-client-handoff" { value 4; description "EoGRE client mobility handoff"; } enum "match-eogre-client-ft-info" { value 5; description "EoGRE client standalone AP recover"; } enum "match-error" { value 6; description "client classification error"; } } description "Enum for matching client type to eogre"; } typedef enm-hs20-supported-version { type enumeration { enum "hs20-r1" { value 0; description "Hotspot 2.0 Release 1"; } enum "hs20-r2" { value 1; description "Hotspot 2.0 Release 2"; } enum "hs20-r3" { value 2; description "Hotspot 2.0 Release 3"; } } description "Enum for hotspot release version"; } typedef mcs-index { type enumeration { enum "he-mcs-index-7" { value 7; description "Config MCS data rate for index 7"; } enum "he-mcs-index-9" { value 9; description "Config MCS data rate for index 9"; } enum "he-mcs-index-11" { value 11; description "Config MCS data rate for index 11"; } } description "Enum for Dot11ax MCS Data rate index"; } typedef enm-wlan-mdns-sd-cfg { type enumeration { enum "mdns-sd-bridging" { value 0; description "Option for enabling MDNS bridging on WLAN"; } enum "mdns-sd-drop" { value 1; description "Option for dropping MDNS packets on WLAN"; } enum "mdns-sd-gateway" { value 2; description "Option for enabling MDNS gateway on WLAN"; } } description "enum for MDNS mode configuration"; } typedef enm-channel-switch-mode { type enumeration { enum "chan-switch-mode-loud" { value 0; description "Channel switch mode loud"; } enum "chan-switch-mode-quiet" { value 1; description "Channel switch mode quiet"; } } description "Enum for channel switch mode"; } typedef rrm-channel-change-reason { type enumeration { enum "chan-change-local" { value 0; description "RRM channel change reason is local"; } enum "chan-change-auto" { value 1; description "RRM channel change reason is auto"; } enum "chan-change-auto-default" { value 2; description "RRM channel change reason is auto default"; } enum "chan-change-static" { value 3; description "RRM channel change reason is static"; } enum "chan-change-static-default" { value 4; description "RRM channel change reason is static default"; } enum "chan-change-radar" { value 5; description "RRM channel change reason is radar"; } enum "chan-change-radar-clear" { value 6; description "RRM channel change reason is radar clear"; } enum "chan-change-edrrm" { value 7; description "RRM channel change reason is Event-driven RRM"; } enum "chan-change-rldp" { value 8; status deprecated; description "RRM channel change reason is RLDP"; } enum "chan-change-intf" { value 9; description "RRM channel change reason is Interference"; } enum "chan-change-unknown" { value 10; description "RRM channel change reason is unknown"; } } description "RRM channel change reason"; } typedef enm-multicast-data-rate { type enumeration { enum "mcast-data-rate-default" { value 0; description "Multicast data rate default"; } enum "mcast-data-rate-6m" { value 6; description "Multicast data rate 6M"; } enum "mcast-data-rate-9m" { value 9; description "Multicast data rate 9M"; } enum "mcast-data-rate-12m" { value 12; description "Multicast data rate 12M"; } enum "mcast-data-rate-18m" { value 18; description "Multicast data rate 18M"; } enum "mcast-data-rate-24m" { value 24; description "Multicast data rate 24M"; } enum "mcast-data-rate-36m" { value 36; description "Multicast data rate 36M"; } enum "mcast-data-rate-48m" { value 48; description "Multicast data rate 48M"; } enum "mcast-data-rate-54m" { value 54; description "Multicast data rate 54M"; } } description "Enum for Multicast data rate"; } typedef calendar-recurrence { type enumeration { enum "daily-recurrence" { value 0; description "Daily recurrence"; } enum "weekly-recurrence" { value 1; description "Calendar of weekly recurrence"; } enum "monthly-recurrence" { value 2; description "Calender of monthly recurrence"; } } description "Calendar profile recurrence"; } typedef reg-domain-status { type enumeration { enum "regulatory-domain-check-status-not-set" { value 0; description "Regulatory Domain check status is Set"; } enum "regulatory-domain-check-status-set" { value 1; description "Regulatory Domain check status is Not Set"; } } description "Regulatory domain check status"; } typedef enum-dual-radio-capable { type enumeration { enum "radio-service-default" { value 0; description "AP radio service not dual radio capable"; } enum "radio-service-dual-mode" { value 1; description "AP radio service dual mode"; } } description "Dual radio capability of AP radio"; } typedef enum-radio-mode-op { type enumeration { enum "dual-radio-mode-op-none" { value 0; description "AP radio dual radio mode operation is not applicable as it is not dual radio capable"; } enum "dual-radio-mode-op-auto" { value 1; description "AP radio dual radio mode operation auto"; } enum "dual-radio-mode-op-manual" { value 2; description "AP radio dual radio mode operation manual"; } } description "Dual radio mode operation of AP radio"; } typedef enum-dual-radio-mode { type enumeration { enum "dual-radio-mode-none" { value 0; description "AP radio dual radio mode is not applicable as it is not dual radio capable"; } enum "dual-radio-mode-enabled" { value 1; description "AP radio dual radio mode enabled"; } enum "dual-radio-mode-disabled" { value 2; description "AP radio dual radio mode disabled"; } } description "Dual radio mode of AP radio"; } typedef enum-radio-fra-capable { type enumeration { enum "radio-fra-capable-default" { value 0; description "AP radio not FRA capable"; } enum "radio-fra-capable" { value 1; description "AP radio FRA capable"; } } description "FRA capability of AP radio"; } typedef timer-profile-action { type enumeration { enum "timer-action-invalid" { value 0; description "Timer action invalid"; } enum "timer-action-wlan-enable" { value 1; description "Timer action wlan enable"; } enum "timer-action-deny-client" { value 2; description "Timer action deny client"; } } description "timer profile actions"; } typedef ipv6-proxy { type enumeration { enum "no-proxy" { value 0; description "Specifies IPv6 Neighbor Discovery(ND) proxy configuration as disabled"; } enum "dad-proxy" { value 1; description "Specifies IPv6 Neighbor Discovery(ND) proxy state as DAD proxy"; } enum "full-proxy" { value 2; description "Specifies IPv6 Neighbor Discovery(ND) proxy state as full proxy"; } } description "Enum to denote IPv6 Neighbor Discovery(ND) proxy configuration type"; } typedef nac-type { type enumeration { enum "nac-support-radius" { value 0; description "Radius NAC"; } enum "nac-support-xwf" { value 1; description "Express Wi-Fi NAC"; } } description "NAC type"; } typedef enm-admin-status { type enumeration { enum "admin-state-enabled" { value 1; description "Set admin state"; } enum "admin-state-disabled" { value 2; description "Disable admin state"; } } description "Admin status"; } typedef enm-lan-port-config { type enumeration { enum "set-port-mode" { value 0; description "Port status"; } enum "set-poe-state" { value 1; description "PoE status for port"; } enum "set-power-level" { value 2; description "Power level for port"; } } description "Enumeration for AP LAN port configuration"; } typedef ble-ltx-admin-state { type enumeration { enum "ble-admin-state-off" { value 0; description "BLE Management admin state is off"; } enum "ble-admin-state-on" { value 1; description "BLE Management admin state is on"; } } description "This object specifies the administrative status selected for BLE Management"; } typedef ble-ltx-vibeacon-status { type enumeration { enum "ble-vibeacon-status-off" { value 0; description "The viBeacon profile status is off"; } enum "ble-vibeacon-status-on" { value 1; description "The viBeacon profile status is on"; } } description "This object specifies the viBeacon profile status"; } typedef ble-ltx-scan-state { type enumeration { enum "ble-scan-state-off" { value 0; description "BLE Management scan status is off"; } enum "ble-scan-state-on" { value 1; description "BLE Management scan status is on"; } } description "This object specifies the scan status selected for BLE Management"; } typedef ble-ltx-scan-filter { type enumeration { enum "ble-scan-filter-off" { value 0; description "BLE Management scan filter is off"; } enum "ble-scan-filter-on" { value 1; description "BLE Management scan filter is on"; } } description "This object specifies the scan mode selected for BLE Management"; } typedef ble-ltx-iot-feature { type enumeration { enum "ble-iot-feature-ble" { value 0; description "The BLE feature is active"; } enum "ble-iot-feature-zigbee" { value 1; description "The Zigbee feature is active"; } enum "ble-iot-feature-other" { value 2; description "The Other feature is active"; } } description "This object specifies the dot15 feature mode"; } typedef ble-ltx-mode { type enumeration { enum "ble-mode-native" { value 0; description "The native BLE mode is active"; } enum "ble-mode-iox" { value 1; description "The IOx BLE mode is active"; } } description "This object specifies the BLE mode"; } typedef ble-no-adv-profile-state { type enumeration { enum "ble-no-adv-profile-disable" { value 0; description "No advertisement profile is disabled"; } enum "ble-no-adv-profile-enable" { value 1; description "No advertisement profile is enabled"; } } description "Specifies the no advertisement profile for BLE management"; } typedef ble-ltx-device { type enumeration { enum "ble-ltx-device-msm1" { value 0; description "Integrated interface"; } enum "ble-ltx-device-s1" { value 1; description "Integrated interface"; } enum "ble-ltx-device-hs0" { value 2; description "Integrated interface"; } enum "ble-ltx-device-usb0" { value 3; description "USB dongle"; } enum "ble-ltx-device-xrusb0" { value 4; description "Integrated interface"; } enum "ble-ltx-device-h0" { value 5; description "Integrated interface"; } enum "ble-ltx-device-sim-if" { value 6; description "Integrated interface"; } enum "ble-ltx-device-unknown" { value 7; description "Unknown interface"; } } description "Enumeration of all the supported BLE devices"; } typedef ble-ltx-device-state { type enumeration { enum "ble-dev-state-invalid" { value 0; description "The BLE device is in invalid state"; } enum "ble-dev-state-init" { value 1; description "The BLE device is in init state"; } enum "ble-dev-state-open" { value 2; description "The BLE device is in open state"; } enum "ble-dev-state-close" { value 3; description "The BLE device is in closed state"; } enum "ble-dev-state-delayed-open" { value 4; description "The BLE device is in delayed open state"; } enum "ble-dev-state-oir" { value 5; description "The BLE device is in Online Insertion and Removal state"; } enum "ble-dev-state-reset" { value 6; description "The BLE device is in reset state"; } enum "ble-dev-state-unsupported" { value 7; description "The BLE device is in unsupported state"; } enum "ble-dev-state-zigbee" { value 8; description "The BLE device is in Zigbee state"; } enum "ble-dev-state-iox-ble" { value 9; description "The BLE device is in IOx BLE state"; } } description "This object specifies the state of BLE device of AP"; } typedef ble-ltx-profile { type enumeration { enum "ble-profile-ibeacon" { value 0; description "The active chirping profile is iBeacon"; } enum "ble-profile-eddy-uid" { value 1; description "The active chirping profile is Eddystone UID"; } enum "ble-profile-eddy-url" { value 2; description "The active chirping profile is Eddystone URL"; } enum "ble-profile-location" { value 3; description "The active chirping profile is Location"; } enum "ble-profile-custom" { value 4; description "The active chirping profile is Custom"; } enum "ble-profile-not-set" { value 5; description "The active chirping profile is not set"; } } description "This object specifies the active chirping profile of BLE"; } typedef ble-ltx-module-type { type enumeration { enum "ble-module-unsupported" { value 0; description "Unsupported BLE module"; } enum "ble-module-internal" { value 1; description "Internal BLE module"; } enum "ble-module-external" { value 2; description "External BLE module"; } } description "This object specifies the BLE module type"; } typedef ble-ltx-antenna-mode { type enumeration { enum "ble-antenna-mode-not-applicable" { value 0; description "BLE antenna mode not applicable"; } enum "ble-antenna-mode-omni" { value 1; description "Antenna mode is omni directional"; } } description "This object specifies the BLE antenna mode"; } typedef ble-ltx-antenna-diversity-status { type enumeration { enum "ble-diversity-not-applicable" { value 0; description "BLE antenna diversity status not applicable"; } enum "ble-diversity-enabled" { value 1; description "BLE antenna diversity status enabled"; } } description "This object specifies the BLE antenna diversity status"; } typedef enm-radio-dot11-proto-supported { type enumeration { enum "protocol-80211a" { value 0; description "Highest throughput supported by radio is as per 802.11a"; } enum "protocol-80211bg" { value 1; description "Highest throughput supported by radio is as per 802.11bg"; } enum "protocol-80211n" { value 2; description "Highest throughput supported by radio is as per 802.11n"; } enum "protocol-80211ac" { value 3; description "Highest throughput supported by radio is as per 802.11ac"; } enum "protocol-80211ax" { value 4; description "Highest throughput supported by radio is as per 802.11ax"; } } description "Highest throughput supported by radio as per 802.11 protocols"; } typedef dot11k-rm-beacon-measurement-scan-report-number-requests { type enumeration { enum "request-once" { value 0; description "One Time Request for 802.11k RM Beacon Measurement in Client Scan Report"; } enum "request-periodic" { value 1; description "Periodic Request for 802.11k RM Beacon Measurement in Client Scan Report"; } } description "Number of 802.11k RM Beacon Measurement Requests for Client Scan Reports"; } typedef dot11k-rm-beacon-measurement-scan-report-measurement-modes { type enumeration { enum "mode-passive" { value 0; description "Passive Measurement Mode for 802.11k RM Beacon Measurement in Client Scan Report"; } enum "mode-active" { value 1; description "Active Measurement Mode for 802.11k RM Beacon Measurement in Client Scan Report"; } enum "mode-table" { value 2; description "Table Measurement Mode for 802.11k RM Beacon Measurement in Client Scan Report"; } } description "Measurement Modes for 802.11k RM Beacon Measurement Requests for Client Scan Reports"; } typedef dot11k-rm-beacon-measurement-scan-report-triggers { type enumeration { enum "trigger-assoc" { value 0; description "802.11k RM Beacon Measurement Request for Client Scan Report triggered automatically by client association"; } enum "trigger-roam" { value 1; description "802.11k RM Beacon Measurement Request for Client Scan Report triggered automatically by client roam"; } enum "trigger-on-demand" { value 2; description "802.11k RM Beacon Measurement Request for Client Scan Report triggered on-demand by EXEC CLI"; } } description "Triggers to send 802.11k RM Beacon Measurement Requests for Client Scan Reports"; } typedef app-type { type enumeration { enum "app-mdns" { value 0; description "MDNS application"; } } description "Applications that support rule configurations"; } typedef rule-action { type enumeration { enum "rule-action-unconfigured" { value 0; description "Action unconfigured"; } enum "rule-action-mdns-grouping" { value 1; description "Group APs for MDNS application"; } } description "Supported rule actions"; } typedef support-bundle-status { type enumeration { enum "supp-bundle-none" { value 0; description "Support bundle file transfer not initialised"; } enum "supp-bundle-copy-init" { value 1; description "Support bundle file transfer initialised"; } enum "supp-bundle-copy-failed" { value 2; description "Support bundle file transfer failed"; } enum "supp-bundle-copied" { value 3; description "Support bundle file transfer successful"; } } description "Status of support bundle file transfer"; } typedef enm-controller-name-status { type enumeration { enum "controller-name-enable" { value 1; description "Configures controller name in access point"; } enum "controller-name-disable" { value 2; description "Clears controller name from access point"; } } description "Controller name status in access point"; } typedef support-bundle-transfer-mode { type enumeration { enum "bundle-transfer-mode-tftp" { value 0; description "Support bundle file transfer mode is TFTP"; } enum "bundle-transfer-mode-scp" { value 1; description "Support bundle file transfer mode is SCP"; } } description "Support bundle file transfer mode"; } typedef ndp-capability { type enumeration { enum "ndp-off-channel-capable" { value 0; description "Neighbor discovery packets are transmitted off channel"; } enum "ndp-on-channel-capable" { value 1; description "Neighbor discovery packets are transmitted on serving channel"; } enum "ndp-on-off-channel-capable" { value 2; description "AP has the capability of transmitting neighbor discovery packets on both on channel and off channel"; } } description "AP neighbor discovery mode capability"; } typedef enm-ndp-mode { type enumeration { enum "ndp-mode-auto" { value 0; description "AP neighbor discovery operation type is auto"; } enum "ndp-mode-off-channel" { value 1; description "AP neighbor discovery is on off channel"; } } description "Enum to represent the AP neighbor discovery operation type"; } typedef enm-antenna-if-type { type enumeration { enum "antenna-none" { value 0; description "No external SIA antenna is connected to the SIA capable AP"; } enum "antenna-rptnc" { value 1; description "SIA RP-TNC antenna is present for the AP radio"; } enum "antenna-n" { value 2; description "SIA N-Type antenna is present for the AP radio"; } enum "antenna-dart" { value 3; description "SIA DART antenna is present for the AP radio"; } } description "AP antenna interface type"; } typedef enm-radio-service-type { type enumeration { enum "radio-service-type-single" { value 0; description "Dual-mode radio is not configurable. 802.11a radio has service type default"; } enum "radio-service-type-dual" { value 1; description "Dual-mode radio can be configured for 802.11a radio"; } } description "AP radio service type"; } typedef country-code { type enumeration { enum "ad" { value 0; description "Country code for Andorra"; } enum "ae" { value 1; description "Country code for United Arab Emirates"; } enum "af" { value 2; description "Country code for Afghanistan"; } enum "ag" { value 3; description "Country code for Antigua and Barbuda"; } enum "ai" { value 4; description "Country code for Anguilla"; } enum "al" { value 5; description "Country code for Albania"; } enum "am" { value 6; description "Country code for Armenia"; } enum "ao" { value 7; description "Country code for Angola"; } enum "aq" { value 8; description "Country code for Antarctica"; } enum "ar" { value 9; description "Country code for Argentina"; } enum "as" { value 10; description "Country code for American Samoa"; } enum "at" { value 11; description "Country code for Austria"; } enum "au" { value 12; description "Country code for Australia"; } enum "aw" { value 13; description "Country code for Aruba"; } enum "ax" { value 14; description "Country code for Aland Islands"; } enum "az" { value 15; description "Country code for Azerbaijan"; } enum "ba" { value 16; description "Country code for Bosnia"; } enum "bb" { value 17; description "Country code for Barbados"; } enum "bd" { value 18; description "Country code for Bangladesh"; } enum "be" { value 19; description "Country code for Belgium"; } enum "bf" { value 20; description "Country code for Burkina Faso"; } enum "bg" { value 21; description "Country code for Bulgaria"; } enum "bh" { value 22; description "Country code for Bahrain"; } enum "bi" { value 23; description "Country code for Burundi"; } enum "bj" { value 24; description "Country code for Benin"; } enum "bl" { value 25; description "Country code for Saint Barthelemy "; } enum "bm" { value 26; description "Country code for Bermuda"; } enum "bn" { value 27; description "Country code for Brunei"; } enum "bo" { value 28; description "Country code for Bolivia"; } enum "bq" { value 29; description "Country code for Bonaire"; } enum "br" { value 30; description "Country code for Brazil"; } enum "bs" { value 31; description "Country code Bahamas"; } enum "bt" { value 32; description "Country code Bhutan"; } enum "bv" { value 33; description "Country code for Bouvet Island"; } enum "bw" { value 34; description "Country code for Botswana"; } enum "by" { value 35; description "Country code for Belarus"; } enum "bz" { value 36; description "Country code for Belize"; } enum "ca" { value 37; description "Country code for Canada"; } enum "cc" { value 38; description "Country code for Cocos (Keeling) Islands"; } enum "cd" { value 39; description "Country code for Congo"; } enum "cf" { value 40; description "Country code for Central African Republic"; } enum "cg" { value 41; description "Country code for Congo"; } enum "ch" { value 42; description "Country code for Switzerland"; } enum "ci" { value 43; description "Country code for Cote de Ivoire"; } enum "ck" { value 44; description "Country code for Cook Islands"; } enum "cl" { value 45; description "Country code for Chile"; } enum "cm" { value 46; description "Country code for Cameroon"; } enum "cn" { value 47; description "Country code for China"; } enum "co" { value 48; description "Country code for Colombia"; } enum "cr" { value 49; description "Country code for Costa Rica"; } enum "cu" { value 50; description "Country code for Cuba"; } enum "cv" { value 51; description "Country code for Cabo Verde"; } enum "cw" { value 52; description "Country code for Curacao"; } enum "cx" { value 53; description "Country code for Christmas Island"; } enum "cy" { value 54; description "Country code for Cyprus"; } enum "cz" { value 55; description "Country code for Czechia"; } enum "de" { value 56; description "Country code for Germany"; } enum "dj" { value 57; description "Country code for Djibouti"; } enum "dk" { value 58; description "Country code for Denmark"; } enum "dm" { value 59; description "Country code for Dominica"; } enum "do" { value 60; description "Country code Dominican Republic"; } enum "dz" { value 61; description "Country code for Algeria"; } enum "ec" { value 62; description "Country code for Ecuador"; } enum "ee" { value 63; description "Country code for Estonia"; } enum "eg" { value 64; description "Country code for Egypt"; } enum "eh" { value 65; description "Country code for Western Sahara"; } enum "el" { value 66; description "Country code for El Salvador"; } enum "er" { value 67; description "Country code for Eritrea"; } enum "es" { value 68; description "Country code for Spain"; } enum "et" { value 69; description "Country code for Ethiopia"; } enum "fi" { value 70; description "Country code for Finland"; } enum "fj" { value 71; description "Country code for Fiji"; } enum "fk" { value 72; description "Country code for Falkland Islands"; } enum "fm" { value 73; description "Country code for Micronesia"; } enum "fo" { value 74; description "Country code for Faroe Islands"; } enum "fr" { value 75; description "Country code for France"; } enum "ga" { value 76; description "Country code for Gabon"; } enum "gb" { value 77; description "Country code for United Kingdom of Great Britain and Northern Ireland"; } enum "gd" { value 78; description "Country code for Grenada"; } enum "ge" { value 79; description "Country code for Georgia"; } enum "gf" { value 80; description "Country code for French Guiana"; } enum "gg" { value 81; description "Country code for Guernsey"; } enum "gh" { value 82; description "Country code for Ghana"; } enum "gi" { value 83; description "Country code for Gibraltar"; } enum "gl" { value 84; description "Country code for Greenland"; } enum "gm" { value 85; description "Country code for Gambia"; } enum "gn" { value 86; description "Country code for Guinea"; } enum "gp" { value 87; description "Country code for Guadeloupe"; } enum "gq" { value 88; description "Country code for Equatorial Guinea"; } enum "gr" { value 89; description "Country code for Greece"; } enum "gs" { value 90; description "Country code for South Georgia and the South Sandwich Islands"; } enum "gt" { value 91; description "Country code for Guatemala"; } enum "gu" { value 92; description "Country code for Guam"; } enum "gw" { value 93; description "Country code for Guinea-Bissau"; } enum "gy" { value 94; description "Country code for Guyana"; } enum "hk" { value 95; description "Country code for Hong Kong"; } enum "hm" { value 96; description "Country code for Heard Island and McDonald Islands"; } enum "hn" { value 97; description "Country code for Honduras"; } enum "hr" { value 98; description "Country code for Croatia"; } enum "ht" { value 99; description "Country code for Haiti"; } enum "hu" { value 100; description "Country code for Hungary"; } enum "id" { value 101; description "Country code for Indonesia"; } enum "ie" { value 102; description "Country code for Ireland"; } enum "il" { value 103; description "Country code for Israel"; } enum "im" { value 104; description "Country code for Isle of Man"; } enum "in" { value 105; description "Country code for India"; } enum "io" { value 106; description "Country code for British Indian Ocean Territory"; } enum "iq" { value 107; description "Country code for Iraq"; } enum "ir" { value 108; description "Country code for Iran"; } enum "is" { value 109; description "Country code for Iceland"; } enum "it" { value 110; description "Country code for Italy"; } enum "je" { value 111; description "Country code for Jersey"; } enum "jm" { value 112; description "Country code for Jamaica"; } enum "jo" { value 113; description "Country code for Jordan"; } enum "jp" { value 114; description "Country code for Japan"; } enum "j2" { value 115; description "Country code for Japan 2(P) "; } enum "j3" { value 116; description "Country code for Japan 3(U) "; } enum "j4" { value 117; description "Country code for Japan 4(Q) "; } enum "ke" { value 118; description "Country code for Kenya"; } enum "kg" { value 119; description "Country code for Kyrgyzstan"; } enum "kh" { value 120; description "Country code for Cambodia"; } enum "ki" { value 121; description "Country code for Kiribati"; } enum "km" { value 122; description "Country code for Comoros"; } enum "kn" { value 123; description "Country code for Saint Kitts and Nevis"; } enum "kp" { value 124; description "Country code for Democratic People's Republic of Korea"; } enum "kr" { value 125; description "Country code for Republic of Korea"; } enum "kw" { value 126; description "Country code for Kuwait"; } enum "ky" { value 127; description "Country code for Cayman Islands"; } enum "kz" { value 128; description "Country code for Kazakhstan"; } enum "la" { value 129; description "Country code for Lao People's Democratic Republic"; } enum "lb" { value 130; description "Country code for Lebanon"; } enum "lc" { value 131; description "Country code for Saint Lucia"; } enum "li" { value 132; description "Country code for Liechtenstein"; } enum "lk" { value 133; description "Country code for Sri Lanka"; } enum "lr" { value 134; description "Country code for Liberia"; } enum "ls" { value 135; description "Country code for Lesotho"; } enum "lt" { value 136; description "Country code for Lithuania"; } enum "lu" { value 137; description "Country code for Luxembourg"; } enum "lv" { value 138; description "Country code for Latvia"; } enum "ly" { value 139; description "Country code for Libya"; } enum "ma" { value 140; description "Country code for Morocco"; } enum "mc" { value 141; description "Country code for Monaco"; } enum "md" { value 142; description "Country code for Republic of Moldova"; } enum "me" { value 143; description "Country code for Montenegro"; } enum "mf" { value 144; description "Country code for Saint Martin (French part)"; } enum "mg" { value 145; description "Country code for Madagascar"; } enum "mh" { value 146; description "Country code for Marshall Islands"; } enum "mk" { value 147; description "Country code for North Macedonia"; } enum "ml" { value 148; description "Country code for Mali"; } enum "mm" { value 149; description "Country code for Myanmar"; } enum "mn" { value 150; description "Country code for Mongolia"; } enum "mo" { value 151; description "Country code for Macao"; } enum "mp" { value 152; description "Country code for Northern Mariana Islands"; } enum "mq" { value 153; description "Country code for Martinique"; } enum "mr" { value 154; description "Country code for Mauritania"; } enum "ms" { value 155; description "Country code for Montserrat"; } enum "mt" { value 156; description "Country code for Malta"; } enum "mu" { value 157; description "Country code for Mauritius"; } enum "mv" { value 158; description "Country code for Maldives"; } enum "mw" { value 159; description "Country code for Malawi"; } enum "mx" { value 160; description "Country code for Mexico"; } enum "my" { value 161; description "Country code for Malaysia"; } enum "mz" { value 162; description "Country code for Mozambique"; } enum "na" { value 163; description "Country code for Namibia"; } enum "nc" { value 164; description "Country code for New Caledonia"; } enum "ne" { value 165; description "Country code for Niger"; } enum "nf" { value 166; description "Country code for Norfolk Island"; } enum "ng" { value 167; description "Country code for Nigeria"; } enum "ni" { value 168; description "Country code for Nicaragua"; } enum "nl" { value 169; description "Country code for Netherlands"; } enum "no" { value 170; description "Country code for Norway"; } enum "np" { value 171; description "Country code for Nepal"; } enum "nr" { value 172; description "Country code for Nauru"; } enum "nu" { value 173; description "Country code for Niue"; } enum "nz" { value 174; description "Country code for New Zealand"; } enum "om" { value 175; description "Country code for Oman"; } enum "pa" { value 176; description "Country code for Panama"; } enum "pe" { value 177; description "Country code for Peru"; } enum "pf" { value 178; description "Country code for French Polynesia"; } enum "pg" { value 179; description "Country code for Papua New Guinea"; } enum "ph" { value 180; description "Country code for Philippines"; } enum "pk" { value 181; description "Country code for Pakistan"; } enum "pl" { value 182; description "Country code for Poland"; } enum "pm" { value 183; description "Country code for Saint Pierre and Miquelon"; } enum "pn" { value 184; description "Country code for Pitcairn"; } enum "pr" { value 185; description "Country code for Puerto Rico"; } enum "ps" { value 186; description "Country code State of Palestine"; } enum "pt" { value 187; description "Country code for Portugal"; } enum "pw" { value 188; description "Country code for Palau"; } enum "py" { value 189; description "Country code for Paraguay"; } enum "qa" { value 190; description "Country code for Qatar"; } enum "re" { value 191; description "Country code for Reunion"; } enum "ro" { value 192; description "Country code for Romania"; } enum "rs" { value 193; description "Country code for Serbia"; } enum "ru" { value 194; description "Country code for Russian Federation"; } enum "rw" { value 195; description "Country code for Rwanda"; } enum "sa" { value 196; description "Country code for Saudi Arabia"; } enum "sb" { value 197; description "Country code for Solomon Islands"; } enum "sc" { value 198; description "Country code for Seychelles"; } enum "sd" { value 199; description "Country code for Sudan"; } enum "se" { value 200; description "Country code for Sweden"; } enum "sg" { value 201; description "Country code for Singapore"; } enum "sh" { value 202; description "Country code for Saint Helena, Ascension and Tristan da Cunha"; } enum "si" { value 203; description "Country code for Slovenia"; } enum "sj" { value 204; description "Country code for Svalbard and Jan Mayen"; } enum "sk" { value 205; description "Country code for Slovakia"; } enum "sl" { value 206; description "Country code for Sierra Leone"; } enum "sm" { value 207; description "Country code for San Marino"; } enum "sn" { value 208; description "Country code for Senegal"; } enum "so" { value 209; description "Country code for Somalia"; } enum "sr" { value 210; description "Country code for Suriname"; } enum "ss" { value 211; description "Country code for South Sudan"; } enum "st" { value 212; description "Country code for Sao Tome and Principe"; } enum "sv" { value 213; description "Country code for El Salvador"; } enum "sx" { value 214; description "Country code for Sint Maarten (Dutch part)"; } enum "sy" { value 215; description "Country code for Syrian Arab Republic"; } enum "sz" { value 216; description "Country code for Eswatini"; } enum "tc" { value 217; description "Country code for Turks and Caicos Islands"; } enum "td" { value 218; description "Country code for Chad"; } enum "tf" { value 219; description "Country code for French Southern Territories"; } enum "tg" { value 220; description "Country code for Togo"; } enum "th" { value 221; description "Country code for Thailand"; } enum "ti" { value 222; description "Country code for Trinidad"; } enum "tj" { value 223; description "Country code for Tajikistan"; } enum "tk" { value 224; description "Country code for Tokelau"; } enum "tl" { value 225; description "Country code for Timor Leste"; } enum "tm" { value 226; description "Country code for Turkmenistan"; } enum "tn" { value 227; description "Country code for Tunisia"; } enum "to" { value 228; description "Country code for Tonga"; } enum "tr" { value 229; description "Country code for Turkey"; } enum "tt" { value 230; description "Country code for Trinidad and Tobago"; } enum "tv" { value 231; description "Country code for Tuvalu"; } enum "tw" { value 232; description "Country code for Taiwan, Province of China"; } enum "tz" { value 233; description "Country code for Tanzania, United Republic of"; } enum "ua" { value 234; description "Country code for Ukraine"; } enum "ug" { value 235; description "Country code for Uganda"; } enum "um" { value 236; description "Country code for United States Minor Outlying Islands"; } enum "us" { value 237; description "Country code for United States of America"; } enum "uy" { value 238; description "Country code for Uruguay"; } enum "uz" { value 239; description "Country code for Uzbekistan"; } enum "va" { value 240; description "Country code for Holy See"; } enum "vc" { value 241; description "Country code for Saint Vincent and the Grenadines"; } enum "ve" { value 242; description "Country code for Venezuela (Bolivarian Republic of)"; } enum "vg" { value 243; description "Country code for Virgin Islands (British)"; } enum "vi" { value 244; description "Country code for Virgin Islands (U.S.)"; } enum "vn" { value 245; description "Country code for Viet Nam"; } enum "vu" { value 246; description "Country code for Vanuatu"; } enum "wf" { value 247; description "Country code for Wallis and Futuna"; } enum "ws" { value 248; description "Country code for Samoa"; } enum "ye" { value 249; description "Country code for Yemen"; } enum "yt" { value 250; description "Country code for Mayotte"; } enum "za" { value 251; description "Country code for South Africa"; } enum "zm" { value 252; description "Country code for Zambia"; } enum "zw" { value 253; description "Country code for Zimbabwe"; } enum "unconfigured" { value 254; description "Country code not configured"; } } description "Country code"; } typedef enm-beam-selection-mode { type enumeration { enum "beam-select-no-config" { value 0; description "Beam selection is not configured for AP radio"; } enum "beam-select-wide" { value 1; description "Wide beam antenna selection for AP radio"; } enum "beam-select-narrow" { value 2; description "Narrow beam antenna selection for AP radio"; } enum "beam-select-narrow-10" { value 3; description "Narrow beam antenna selection with a tilt of 10 degrees from centre"; } enum "beam-select-narrow-20" { value 4; description "Narrow beam antenna selection with a tilt of 20 degrees from centre"; } } description "Beam selection mode for AP radio"; } typedef enm-reset-reason { type enumeration { enum "reset-user" { value 0; description "Remote leader reset initiated by user"; } enum "reset-auto" { value 1; description "Remote leader reset initiated by system"; } } description "Enumeration specifying remote leader reset reason"; } } // module Cisco-IOS-XE-wireless-enum-types
© 2023 YumaWorks, Inc. All rights reserved.